Skip to Content

Horizontal slurry pumps

Schegler® horizontal slurry pumps: Vigor™ and Gravel™

Heavy-duty horizontal slurry pumps for abrasive and corrosive slurries. Vigor™ covers discharge sizes from 25 to 450 mm, up to 5000 m³/h and 70 m head; Gravel™ handles large particles from 100 to 600 mm, up to 9000 m³/h. All Schegler® pumps are completely interchangeable with Warman® pumps and spare parts.

Request a quotationFree on-site assessment

Schegler Vigor horizontal slurry pump

Why Schegler®

Modular wet end

All wet-end parts are replaceable and interchangeable without modifying the pump. Replaceable liners protect the cover plate and frame plate.

Cartridge bearing assembly

The bearing assembly can be replaced separately, without dismantling the base. Available in heavy-duty and extra heavy-duty grease-lubricated versions, and oil-lubricated.

In-situ impeller adjustment

Adjust the impeller clearance on site with the adjustment screw, without shims. A minimal clearance to the throatbush keeps efficiency high and wear low.

Short impeller overhang

A thick shaft and a short overhang give high stiffness: stable sealing, longer bearing life and a high tolerance for solids impact.

Fast inspection

Remove a few bolts and the cover plate for direct access to the wet-end and sealing parts.

Discharge every 45°

The discharge can be oriented in steps of 45°, so the pump fits your existing piping.

Schegler Vigor horizontal slurry pump

Vigor™ Horizontal Series


  • Discharge sizes 25 to 450mm (1″ to 18″)
  • Capacity through 5000m³/h
  • Heads through 70m


This horizontal slurry pump is designed for applications where abrasive or corrosive liquids with particles must be pumped. Fluids can range from wastewater to abrasive slurries.

Numerous industries rely upon Vigor’s robust modular construction for countless applications, making this highly adaptable slurry pump tested and tried in the most severe conditions.

The wet end parts of this pump are entirely replaceable, which facilitates inspections and provides ease of maintenance. The unparalleled wear resistance of its wet end parts makes Vigor a high-performance slurry pump requiring low maintenance. This results in a reliable, efficient pump with the lowest total cost of ownership for abrasive processes.


Download Brochure

Learn more

Vigor™ Family Curves




Schegler Vigor pump curves


Note: The curves above show pump performance with clean water. The curves should only be used to make a primary selection.  

Schegler Gravel horizontal slurry pump

Gravel™ Horizontal Series


  • Discharge sizes 100 to 600mm (4″ to 24″)
  • Capacity through 9000m³/h
  • Heads through 50m


The Gravel series pumps specialize in efficiently handling abrasive slurries with large particles, combining continuous performance with minimized maintenance and ownership costs. These pumps are constructed robustly, with a modular design that not only facilitates easy maintenance but also ensures flexibility by offering wear components in various highly resistant alloys tailored to specific applications. 

Overall, the Gravel series stands out for its operational efficiency and versatility across various applications. It promises exceptional performance with a focus on reducing the total cost of ownership, marking it as a reliable asset for industries dealing with abrasive and challenging pumping scenarios.


Download Brochure

Learn more

Gravel™ Family Curves




Schegler Gravel pump curves


Note: The curves above show pump performance with clean water. The curves should only be used to make a primary selection.

Gravel™ specification sheets

Our most used impeller shapes

Front vanes limit internal recirculation; back vanes reduce the pressure at the seal. Large, fixed impeller diameters allow low rotation speeds.

5-vane closed

Standard for abrasive duties

2-vane open

For media that tend to clog a closed impeller

6-vane closed

For high-pressure applications

4-vane closed, high efficiency

Where efficiency matters most

These are our most used impeller shapes. Many more are available, such as 3-vane open and closed and 5-vane open impellers, in different materials. Ask our specialists

Our most used sealing systems

The right seal depends on the slurry, the duty and whether any leakage is acceptable. A mechanical seal makes sense for start-stop duty, a high suction head, or where no leakage or product contamination is allowed.

Gland packing

Packing compressed on the shaft sleeve, with pressurised flushing water in the lantern restrictor.

Expeller seal

The expeller rotates in the expeller ring and keeps the slurry away from the shaft.

Single mechanical seal

For process water and coarser slurries below 40 wt% solids, at high and low pressure.

Double mechanical seal

For fine and dense slurries, such as filter press feed, also above 40 wt% solids.

Dry gland seal

For thickener underflow at low pressure, without flushing water.

These are the most common sealing systems. Many more types and configurations are available; we select the right seal for your duty together with you. Ask our specialists

Our most used wear materials

High chrome 423 (27% Cr)

Our standard, for sharp, large and very fine particles, as in metal and plastic recycling.

Natural rubber 662 (50 Shore A)

For round, medium-sized particles, as in sand quarries.

High-chrome molybdenum 420

The wear resistance of 423 with up to a third more toughness, for dredging and sand & gravel with stones.

Read more

These are our most used materials. We offer many more, including other high-chrome alloys, stainless and duplex steels, and other rubbers and elastomers. Ask us for the right material

Frequently asked questions

Vigor™ for abrasive or corrosive liquids with particles, from wastewater to abrasive slurries: 25 to 450 mm, up to 5000 m³/h and 70 m head. Gravel™ for abrasive slurries with large particles: 100 to 600 mm, up to 9000 m³/h and 50 m head.

Yes. All Schegler® pumps are completely interchangeable with Warman® pumps and spare parts.

Gland packing and expeller seals suit most slurry duties. Choose a mechanical seal for start-stop duty, a high suction head or when no leakage is acceptable: single for process water and coarser slurries below 40 wt% solids, double for fine and dense slurries such as filter press feed. A dry gland seal suits thickener underflow at low pressure.

Thanks to the cartridge bearing assembly, the impeller is adjusted on site with an adjustment screw, without shims. Keeping the clearance to the throatbush small maintains efficiency and reduces wear on the impeller and throatbush.

Need help selecting a Schegler® pump?

Share your flow rate, head and slurry data. You receive a quotation within 24 hours.