Schegler® materials engineering
Schegler® material 420: wear-resistant and tough
High-chrome molybdenum cast iron for dredge pumps and sand & gravel applications with coarse solids: the wear resistance of our standard high chrome, with up to a third more toughness.

Dredging demands two things at once
Erosion
Sand and silt continuously scour the impeller, wear plates and suction nozzle. This demands hardness.
Impact
Stones and gravel strike the vanes and suction nozzle at high speed. This demands toughness: the material must not crack or chip.
Traditionally you choose between a longer wear life and less breakage. Material 420 gives you both.
Wear resistance, equal to high chrome 423
Toughness: up to +33% versus 423
Hardness
Chromium carbides, equal to 423
Why it works
25 vol% hard chromium carbides carry the wear from sand and gravel, the same fraction as in 423. An alloyed matrix with 28–29% chromium and about 2% nickel and molybdenum absorbs impact and slows down cracks. The result: stones cause less chipping, and the surface wears evenly instead of cracking.
Our high chromes compared
| Code | Material | Wear | Corrosion | Toughness |
|---|---|---|---|---|
| 425 | High chrome 30% Cr, very hard | 4 | 1 | 1 |
| 423 | High chrome 27% Cr (reference) | 3 | 3 | 3 |
| 420 | High-chrome molybdenum | 3 | 3 | 3.5–4 |
| 439 | High chrome 27% Cr, tough grade | 2 | 4 | 4 |
| 401 | High chrome 33% Cr, corrosion-resistant | 2 | 5 | 4 |
Qualitative scores from 0 to 5, higher is better; 423 is the reference. Indicative, not a specification.
Which material for which duty?
| Situation | Advice |
|---|---|
| Fine sand and silt, few stones | 423 |
| Sand with gravel and stones, regular impact | 420 |
| Very large stones, where even 420 chips | 439 |
| Extreme abrasion, no coarse stones | 425 |
| Acidic or corrosive slurry | 401 · 428 |
Not sure? Let us review the wear pattern of your current parts together: an evenly worn surface points to erosion, chipping and cracks point to impact.
Where 420 makes the difference
- Dredge pumps handling stones and shells
- Sand & gravel extraction, gravel pumps
- Ball mill pumps with a coarse fraction
- Slurry with large solid particles
Parts in 420
- Impellers
- Suction and pressure side wear plates
- Suction nozzle liners
- Volute liners and expellers
Schegler® parts in 420, tailored to your pump
For existing pumps
Also for pumps of other brands, from a drawing or based on your existing part.
One-off pattern cost
The pattern is made once; repeat orders follow without new pattern costs.
Technical advice
Our engineers select the right material for each part together with you.
Stock agreements
Critical parts kept in stock, so your downtime stays limited.
Frequently asked questions
A high-chrome molybdenum cast iron offered under the Schegler® brand, with 28–29% chromium and about 2% nickel. It combines the wear resistance of high chrome 423 with clearly higher toughness.
When your current high-chrome parts mainly show chipping or cracks from stones. An evenly worn surface points to erosion, where 423 is a good choice; chipping points to impact, where 420 performs better.
Impellers, suction and pressure side wear plates, suction nozzle liners and, where needed, volute liners and expellers.
Yes. Based on a drawing or your existing part, we make a pattern once; repeat orders follow without new pattern costs.
Ready for a longer wear life?
Send us a production drawing or a scan of your current part and we prepare a tailored proposal.